Awọn iṣọra fun fifi sori ẹrọ ati ẹrọ idanwo ti iru kio iru ẹrọ iredanu ibọn ï¼ˆä¸ ï¼ ï¼ ‰

Awọnkio iru shot iredanu ẹrọgbogbogbo ni irisi ti o tobi, ati ilana fifi sori ẹrọ jẹ idiju diẹ sii ju ti ẹrọ kekere lọ. Fifi sori ẹrọ to tọ ati ẹrọ idanwo jẹ bọtini lati rii daju iṣiṣẹ deede ti ohun elo nigbamii. Ni ọran ti awọn iṣẹ ibẹrẹ ti ko ni oye, awọn olumulo nilo lati tẹle awọn ilana ti oṣiṣẹ ti o yẹ tabi tọka si awọn ilana naa. Išišẹ laigba aṣẹ le ni rọọrun fa ibajẹ ti ko ṣe yipada sikio shot iredanu ẹrọ. Awọnshot blasting machine manufacturer has sorted out the precautions for installation and test machine to share with you. I hope it will be helpful to users who use the device for the first time.
1. Installation. Awọnkio iru shot iredanu ẹrọ is installed and debugged in the production plant and disassembled into several parts before being transported to the user site for installation. Although there is no pit, the foundation must be firm, the anchor bolt holes must be standardized, and the chamber body must be adjusted. After the second irrigation, the anchor bolt nuts can be tightened after solidification. After the chamber body is fixed, the various parts can be installed. Awọnprecautions for the installation and debugging of the relevant components are introduced below.
1. Ẹrọ iredanu ẹrọ:
Awọnshot blasting device has been installed on the chamber body before leaving the factory. Please pay attention to the problems to be debugged before use. Check whether the fixed positions of the blade, the pill wheel, the directional sleeve, and the guard plate are accurate and firm, and check whether the direction of rotation is correct after power on. Then adjust the position of the directional sleeve opening. Theoretically, the angle between the front edge of the directional opening and the front edge of the blade throwing position is about 900. After fixing the position of the directional sleeve, the position of the projectile belt can be detected by hanging Place a steel plate or wooden board on the position of the workpiece facing the exit of the shot blasting machine, start the shot blasting machine, put a small amount (2-5kg) of projectiles into the blasting tube, and then stop, check whether the hit position on the steel plate is suitable for the needs, such as Close the window of the bias-adjustable directional sleeve downwards, and vice versa, until it fits, and note the position of the directional sleeve opening as a basis for future replacement of the directional sleeve.
2. Hoist ati conveyor dabaru:
Ni akọkọ ṣe idanwo ti ko si fifuye lati ṣayẹwo boya garawa hoisting ati awọn ọbẹ ajija n ṣiṣẹ ni itọsọna to tọ, lẹhinna mu igbanu ti hoist naa pọ si iwọn ẹdọfu ti iwọntunwọnsi lati yago fun iyapa, ati lẹhinna ṣe idanwo fifuye lati ṣayẹwo išišẹ ati agbara gbigbe, boya eyikeyi isokuso Noise ati gbigbọn, ṣayẹwo ati yọ awọn idiwọ kuro.
3. Pill-sand separator:
Ni akọkọ ṣayẹwo boya gbigbe ti àgbo rọ, ati lẹhinna ṣayẹwo ipo to dara ti awo ti o ya sọtọ, lẹhinna nigba ti o ba gbe ati fifa fifa soke, ṣiṣan ṣiṣan ti awọn ibọn irin wa, ati ṣayẹwo boya awọn ibọn irin n ṣan jade ati ja bo nígbà tí a bá ti tú èébú náà